• You are here:  
  • Home
  • Q&A
  • Q&A
  • PowerBuilder
  • Can I try Power Builder 2017 R2 via proxy server ?

Subscribe via RSS
Toggle Submenu
  1. Categories
  2. Recent
  3. Tags
View Replies (2)

Resolved Can I try Power Builder 2017 R2 via proxy server ?

  1. Issue
0
Votes
Undo
  1. Alex Ivanov
    Alex Ivanov
  2. PowerBuilder
  3. Monday, 2 July 2018 14:38 PM UTC

In my company Internet connection exists via proxy. 

I installed trial license, but couldn't establish internet connection.   ( http://localhost/aem        404.0 - Not Found )

It's impossible? 

TIA

Alex

 

Orca error in 'scc get connect properties'. Result...
Powerbuilder WS and IIS
Responses (2)
Armeen Mazda @Appeon
Armeen Mazda @Appeon Accepted Answer Pending Moderation
  1. Monday, 2 July 2018 19:07 PM UTC
  2. PowerBuilder
  3. # 1

I guess you are trying out trial of the PowerServer.  In addition to installing PowerBuilder 2017, you need to make sure you install the PowerServer Toolkit (this will appear as a toolbar in the PB IDE) and install the PowerServer itself to IIS.  Of course, before you install PowerServer to IIS you need to properly install and configure.  Please read the documentation carefully and follow each step - if you miss a step it won't work.

Couple troubleshooting steps to keep in mind:

1. If http://localhost doesn't display the IIS welcome page then most like your IIS is not installed or at least not configured properly

2. If http://localhost/AEM doesn't display the AEM welcome page then either you did not install PowerServer or your IIS is not configured properly with the .NET components PowerServer needs (this is covered in the documentation)

 

PowerServer Installation Guide: https://www.appeon.com/support/documents/appeon_online_help/2017/installation_guide/index.html

Comment
Alex Ivanov
  1. Alex Ivanov
  2. Tuesday, 3 July 2018 12:15 PM UTC
Today I was lucky more.



I logged in AEM, set proxy parameters, but couldn't establish internet connection when I activated PowerServer.



Failed to log in. Please make sure a valid online license is assigned to the account. Error code: 116, error message: No network connection.



I think my proxy settings don't work at all.



TIA 



Alex



 



 

  1. Helpful
Olan Knight
  1. Olan Knight
  2. Tuesday, 3 July 2018 14:30 PM UTC
The IIS settings are extremely specific and tricky. It's easy to miss something.

Go back over the instructions, starting from scratch, and re-set them. Then reboot and verify that IIS is up and running.

THEN start playing with PowerBuilder.





Good Luck,



Olan



 

  1. Helpful
There are no comments made yet.
David Peace (Powersoft)
David Peace (Powersoft) Accepted Answer Pending Moderation
  1. Monday, 2 July 2018 15:17 PM UTC
  2. PowerBuilder
  3. # 2

Hi Alex

The URL looking up on localhost, even if it were via a proxy I would have expected it to be an appeon.com URL. The proxy may then block it, and you would have to get that url enabled in the proxy.

However, I hope that someone from Appeon jumps on here to explain the localhost url?

Cheers

David

Comment
MOHAN KRISHNA DEVARAPU
  1. MOHAN KRISHNA DEVARAPU
  2. Tuesday, 7 January 2020 18:26 PM UTC
Hello Alex,



Same issue,Failed to log in. Please make sure a valid online license is assigned to the account. Error code: 116, error message: No network connection.



Could you please help.



Krish
  1. Helpful
There are no comments made yet.
  • Page :
  • 1


There are no replies made for this question yet.
However, you are not allowed to reply to this question.