1. Olan Knight
  2. PowerBuilder
  3. Friday, 22 September 2017 18:15 PM UTC

Brand new Windows 10, 64 bit o/s VM I have the PB v12.0 CDs on disk I copy them to my C drive into C:\Personal\Downloads\PBv120 I want to install as an evaluation I've tried: 1) Running the "C:\Personal\Downloads\PBv120\Autorun.exe" as Administrator 2) using a cmd prompt: cd \Personal\Downloads\PBv120 autorun -i GUI 3) Running C:\Personal\Downloads\PBv120\PowerBuilder120\setup.exe as an Administrator 4) using a cmd prompt: cd \Personal\Downloads\PBv120\PowerBuilder120\ setup -i GUI In the case of #3: it detects the code was not run from AutoRun and then it closes. In all other cases, the installtion will start, but when it gets to PowerBuilder the Wizard is just an empty frame, and the system locks. Task manager show zero CPU activity at the 1, 5, and 30 minutes marks. HOW can I get PBv12.0 installed???? Thanks, Olan

Gerry Whitmarsh Accepted Answer Pending Moderation
  1. Saturday, 23 September 2017 06:24 AM UTC
  2. PowerBuilder
  3. # 1

Hi,

I tried everything to get PB 12.6 to run on W10 but never succeeded. I had to resort to installing it on a Windows 7 VM. See this thread.

https://archive.sap.com/discussions/thread/3888348

HTH,

Gerry.

Comment
  1. Gerry Whitmarsh
  2. Sunday, 24 September 2017 06:55 AM UTC
Good grief!! I would never have worked this out - kudos. Thank goodness this is in the past as I have upgraded to 2017.

Gerry.

  1. Helpful
  1. Olan Knight
  2. Sunday, 24 September 2017 19:23 PM UTC
I >>> FINALLY got PBv12.1 installed, but it was a nightmare.



Every time I ran the installer, it would process the Wizard up to the point where the installation of PowerBuilder would begin, then the Wizard becase a clear glass pane - no content, and the Task Manager said it was using zero CPU time.



Here's how I ended up making this work:



1) Have an unsaved WORD doc open in the desktop.



2) In the main CD, select the setup.exe, NOT the Autorun.exe

    Ensure there is NO compatibility mode set on the exe, then RUN AS ADMINISTRATOR



3) Get to where the Wizard becomes glass pane and stops

     Do NOT kill the setup.exe task

4) Ctl-alt-end to reboot,

    CANCEL the reboot

5) Click the power button

    CANCEL again

    – and the setup.exe will continue

5)  After the Wizard has completed installing PowerBuilder - and yes, after you have clicked FINISH, a series of dialog boxes will display in an infinite loop of “installing…, extracting…”

6)  Wait for this to finish - anywhere from 5 to 10 minutes.



No, I'm not kidding. This silliness actually worked and installed PB v12.0.

I then ran the EBFs to bring my PB up to v12.1,b7055 which is where we needed to be. I had to use the same trick on every EBF.



Rebooted, and tested PB. It worked.



Later -

Olan



 

  1. Helpful
There are no comments made yet.
Chris Pollach @Appeon Accepted Answer Pending Moderation
  1. Friday, 22 September 2017 18:43 PM UTC
  2. PowerBuilder
  3. # 2

Hi Olan;

   Just a quick note make sure that you know that any PB v12.x version was not certified for W10 - let alone VM'ed one.

My only suggestion would be to start your VM Windows 10 in "safe" mode and see if that helps.

Regards ... Chris

Comment
  1. Olan Knight
  2. Friday, 22 September 2017 18:52 PM UTC
I'll give that a try. Thanks.



 

  1. Helpful
There are no comments made yet.
  • Page :
  • 1


There are no replies made for this question yet.
However, you are not allowed to reply to this question.
We use cookies which are necessary for the proper functioning of our websites. We also use cookies to analyze our traffic, improve your experience and provide social media features. If you continue to use this site, you consent to our use of cookies.